Air Stone not working! [RESOLVED]

Grobo Support
#31

You should be able to see where the female end of that connection goes. Take a peek inside and up. I think you can do this without their help :+1:

1 Like
#32

I’d look at mine, but she’s sleeping right now. Maybe @Azuri, or @chris_barfield can look in their unit to see where it’s plugged in. How bout it guys? :+1::v:

1 Like
#33

I did reach around for what I’d guess to be the female end of the wiring harness to no avail. The camera didn’t help either…unless I am missing something.

IMG_20190707_114501
IMG_20190707_1145013264×2448 1.36 MB
IMG_20190707_114422
IMG_20190707_1144223264×2448 1.71 MB

2 Likes
#34

Did you take the pump out?

1 Like
#35

Yea, the pump it out. The bottom picture is looking through the further elastic restraint for the air pump.

2 Likes
#36

Ok we’ll get the external pump for now. You’ll use it again I’m sure so it’s not wasted money. Here are the two tools they sent me to take off the back. Pick them up too.

image
image3024×4032 1.59 MB
image
image3024×4032 1.98 MB

2 Likes
Unit does not Enter Drain Mode [RESOLVED]
#37

I’ll bet it plugs in right above the other connector in that pic

1 Like
#38

Thanks for the help with which tools to buy, @Osage!

I have the #1 square bit, looks like I need a #0.

3 Likes
#39

First go to a hydro store, or a pet shop and get that pump. You’ll use it eventually anyway, while you’re at it get that second #0 and you’re good to go. After the fix, you will see great improvement in your grow. Sorry this happened to you and sorry it wasn’t diagnosed earlier. Kinda surprised at that :triumph:

4 Likes
#40

I’m actually amazed you got anything at all from your grows. Cannabis is a truly amazing plant. She was starved of oxygen the whole time and she still produced :exploding_head::exploding_head::exploding_head: what strain was it?

3 Likes
#41

It’s easy to get back and side panels off with Phillips head and square. Don’t use power tools, hand tools only. The circuit board is located bottom left of grobo. Taking the back panel off will let u look at that circuit board. U’ll most likely have to take off left panel to really handle those wires which can be tricky(grobo door has to open to remove so make sure ur unlocked before unplugging and disassemble). I had same issue with unplugged wiring.

4 Likes
How do I take the side panel off
#42

@LtcTerps, thanks for the disassembly tips.

@Osage, I’ve been growing Cinderella 99.

3 Likes
#43

Hey guys sorry my flowering room including the grobo are currently sleeping. I’ve not ventured far inside the access hatch since I’ve had no hardware issues to resolve.

Keep us posted if you need a picture later. :+1:

2 Likes
#44

@Osage, is that screwdriver on the left a Phillips head #1 or a Tri-point #1?

2 Likes
#45

Philips # 1x3-1/4”

1 Like
#46

Hey Walter,

I too am amazed you got 13 grams with out any oxygen in your water. Hit me up at support@grobo.io and I’ll get you squared away!

Cheers,
Stephen

3 Likes
#47

@Walter,

((#WelcomeBack))… :wave::wink:

Sorry, this happened to you… Hope your pump gets working and your next grow will be a big improvement… :crossed_fingers::crossed_fingers:

1 Like
#48

Thanks @SilverGrobo.

@Stephen, I’ve already opened a support ticket which I believe you replied to. If not it was another Stephen.

I sorta feel like a moron for not being aware of this sooner. I figured the Grobo aerated intermittently and I just was never there to observe it. Watched water never bubbles??? Anyways, I just figured I sucked at the automated grow thing. Haha

4 Likes
#49

Keep up the food fight brother! You’ll win​:+1::v:

1 Like
#50

Actually I stopped using the system since then because I was soo frustrated I had to get another pump… I just replaced it right now and I’m ready for to start growing again… everything is working fine so far lol… I almost wanted to cry because it was the most expensive magnet holder that I have ever purchased hahaha. Has anything changed since then ?

2 Likes