grobo cleaned and big bud planted!
just got 1 question, I always thought the first fill during germination shouldn’t get any nut, but bottle 3, 4 and 5 clearly got dispensed, is this expected @Todd.grobo?
grobo cleaned and big bud planted!
4 Likes
I thought I read somewhere Stephen said he set up that way to clear or prime the lines.
4 Likes
Right on point Randy!
4 Likes
… #7
- - - [2021-11.15]:
@Arn,
…
.
…
.
.
~~~
@Arn,
…
.
.
-
(Unless Grobo Can Do It On Their End, We Can’t Shut Them Off):
-
-
.
~~~
- - - [2021-12.20]:
@Arn,
.
.
.
-
(You Can If You Want, -But- If It Was My Grow, I Would Let Her Grow Right Under The Second Fan):
-
[‘second fan’]: {
}:
.
~~~
- - - [2021-12.22]:
@Arn,
…
.
.
.
.
-
(This Is Horrible News, There Might Not Be A Better Solution, -Then- To Try And Get The [WaterLevelSensors] Free From Dabri At This Point): (Just Enough To Get To The Sensors To Clean Them):
-
(After The Nutes Doses Sufficient Amount, -Then- Remove The Hoses, -So- They Don’t Over Drink Them): (-Just- Until The Support Can Get To Your Case): (Sharing Their -Resolve- Here Would Be Nice):
-
(Check Both Sensor Before Doing The Next [Drain/Fill]):
-
(Check To See If Your [FirmWare] Is Up To Date):
- - -
@Arn,
…
.
.
.
.
.
.
.
-
(Are You Marking Your Bottles To Make Sure The Nutes Are Really Not Dispersing):?
-
(This Is The Easiest Way To Know If They Are Dispersing Properly After A Complete [Drain/Fill]):
- - -
@Arn,
…
.
-
(For Now I Would Just Take The Bottles Out, -And- Dose The Plant [YourSelf]):
-
(I Would Try [10ml -Or- 15ml] For [3-4-5-Hydroguard If You Have It]):
.
--
~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
3 Likes
Got the same plant 
going right now in my tent 
2 Likes
how do I stop receiving the water change notifications?
1 Like
You don’t. I just acknowledge and close it.
3 Likes
Here we go again on the 5th major annoyance.
The grobo won’t stop draining, possibly to a stuck sensor.
Can’t lift the lid without damaging the root, and I can’t fill because it apparently still has to drain something first.
I tried turning off and on the unit : I was then able to fill the unit, but without any nut being dispensed. it also ended up emptying the whole bottle 2, ph was at 3 when I quickly drained everything.
the second attempt was really similar, but this time around, it emptied half of bottle 1, ph was then up to 8 or 9.
I then did a drain and fill but without bottle 1 and 2 connected, still no nute being dispensed.
1 Like
Put bottle 1 and 2 back, at least they don’t seem to be emptied in the tank for now.
@Todd.grobo @SilverGrobo do you know why I’m not getting any nut being dispensed?
2 Likes
I tried to move my way through the sensor with my hand, nothing is stuck down there.
did a quick ph check (I already did a callibration 2 weeks ago) and everything was fine.
it has been sitting there for an hour and still no nut.
2 Likes
4th time wasn’t the charm, still nothing.
I’ve created a ticket, but if anyone has any hint at something I could try, definitely up for suggestions.